管道、法兰采购
发送至邮箱
管道、法兰采购
| 招标信息 | |||
|---|---|---|---|
| 招标单位 | (略) | 项目名称 | 管道、法兰 |
| 质保期 | 报名截止日期 | ||
| 招标邮箱 | *@*ttp://** | ||
| 竞标保证金信息 | |||
|---|---|---|---|
| 项目保证金 | 2000.00元 | 帐户名称 | 山东新南 (略) |
| 帐号 | * | 开户行 | 中国银行龙口南山支行 |
| 备注 | |||
| 备注：竞价 (略) 转账，不支持个人名义转账或银行柜台现金转账。 | |||
| 供应审计部招标联系人信息 | |||
|---|---|---|---|
| 标书联系人 | 无 | 办公电话 | 无 |
| 邮件 | 无 | ||
| 标书汇款相关信息 | |||
|---|---|---|---|
| 账户名称 | 无 | 账号 | 无 |
| 开户行 | 无 | 行号 | 无 |
| 标书收费标准 | 地址、电话 | 无 | |
| 备注： (略) 转账，不支持个人名义转账或银行柜台现金转账。注明标书费的用途或投标项目名称。 | |||
| 物品名称 | 规格型号 | 数量 | 单位 | 描述 |
|---|---|---|---|---|
| 双金属复合耐磨直管 | DN450 | 5.00 | 件 | 1.名称：双金属复合耐磨直管 2.规格型号：DN450 3.执行标准：GB/T 26652-2011 4.材质：外管Q345B，内衬KMTBCr28 5.单位：件 6.使用寿命：5年 7.技术要求：直管长度1.5米，两侧带非标法兰,可以直接连接D480×14管道上的DN450标准法兰（A系列）。外管规格D510×10mm，内衬管内径Dn=448mm，管内耐磨层厚度H不低于20，复合管外层采用普通钢管材质Q345B，内衬采用高铬耐磨合金材质KMTBCr28，在高温热铸（焊）状态下整体复合而成，耐磨层硬度不低于HRC46。 8.验收标准：提交材质证明，附产品合格证，来货与技术要求不符，供应商予以免费退换货处理。 |
| 双金属复合耐磨弯头 | DN450 | 2.00 | 件 | 1.名称：双金属复合耐磨弯头 2.规格型号：DN450 3.执行标准：GB/T 26652-2011 4.材质：外管Q345B，内衬KMTBCr28 5.单位：件 6.使用寿命：5年 7.技术要求：弯头为90°两侧带非标法兰, 可以直接连接D480×14管道上的DN450标准法兰（A系列）。弯头外管规格D510×10mm，内衬管内径Dn=448mm，弯头外侧耐磨层厚度H1=22，弯头内侧耐磨层厚度H2=20,复合管外层采用普通钢管材质Q345B，内衬采用高铬耐磨合金材质KMTBCr28，在高温热铸（焊）状态下整体复合而成，耐磨层硬度不低于HRC46，弯头进料方向直管L1长度200mm，出料方向直管L2长度300mm。 8.验收标准：提交材质证明，附产品合格证，来货与技术要求不符，供应商予以免费退换货处理。 |
| 法兰盘 | DN150 | 8.00 | 片 | {"规格型号":"DN150","公称压力":"1.6Mpa","公称通径":"150mm","材质":"Q235B","特殊要求":"密封面需有水纹密封线；使用寿命：≥1095天；螺栓孔数：8孔","参照标准":"GB/T 9124.1-2019","备注":"验收标准：到货与技术要求不符时，供应商无条件退换货处理。"} |
| 法兰盘 | DN100/PN16 | 138.00 | 片 | {"规格型号":"DN100/PN16","公称压力":"1.6Mpa","公称通径":"100mm","材质":"Q235A","特殊要求":"使用寿命2190天,密封面需有水纹密封线.","参照标准":"GB/T 9124.1-2019","备注":"到货与技术附件不符予以退/换货."} |
| 法兰盘 | DN40/PN16 | 2.00 | 片 | {"规格型号":"DN40/PN16","公称压力":"1.6MPa","公称通径":"40mm","材质":"碳钢Q235A"} |
| 法兰盘 | DN50-16 | 24.00 | 片 | {"规格型号":"DN50-16","公称压力":"1.6MPa","公称通径":"50mm","材质":"Q235B/国标","参照标准":"GB/T 9112~9124-2010钢制管法兰"} |
| 法兰盘 | DN32 | 2.00 | 片 | {"规格型号":"DN32","公称压力":"1.6MPa","公称通径":"32mm","材质":"Q235A","参照标准":"GB/T 9119-2010"} |
| 冲压弯头 | Φ89*5/R=5D/90° | 35.00 | 个 | {"规格型号":"Φ89*5/R=5D/90°","公称直径":"89mm","壁厚":"5mm","角度":"90°","弯曲半径":"R=5D","公称压力":"1.6Mpa","材质":"20#钢","使用寿命":"5年"} |
| 冲压弯头 | DN32/20# | 50.00 | 个 | {"规格型号":"DN32/20#","公称直径":"32mm","壁厚":"5mm","角度":"90°","弯曲半径":"R=1.5D","公称压力":"1.6Mpa","材质":"20#钢","使用寿命":"5年"} |
| 冲压弯头 | Φ159*20/R=1.5D/90度 | 5.00 | 件 | {"规格型号":"Φ159*20/R=1.5D/90度","公称直径":"159mm","壁厚":"20mm","表面处理":"表面无残损、锈蚀、碰伤、气孔、夹渣、毛刺","连接方式":"焊接","角度":"90°","弯曲半径":"1.5D","公称压力":"10Mpa","材质":"20#碳钢","特殊要求":"无","使用寿命":"700天","参照标准":"GB/T 12459-2017","备注":"验收标准：厂家到货附带材质报告单及合格证，达不到技术要求，要求厂家无偿换货，在使用过程中达不到使用寿命，要求厂家赔付！"} |
| 冲压弯头 | Φ159*6/R=1.5D/20# | 10.00 | 件 | {"规格型号":"Φ159*6/R=1.5D/20#","公称直径":"159mm","角度":"90°","弯曲半径":"1.5D","公称压力":"1.6MPa","材质":"20#钢"} |
| 冲压弯头 | DN32 | 5.00 | 个 | {"规格型号":"DN32","公称直径":"32mm","角度":"90°","弯曲半径":"48/32","公称压力":"1.6Mpa","材质":"20#钢","使用寿命":"12年"} |
| 冲压弯头 | DN76*5 | 2.00 | 个 | {"规格型号":"DN76*5","公称直径":"76mm","壁厚":"5","角度":"90°","弯曲半径":"114","公称压力":"1.6Mpa","材质":"20#钢","使用寿命":"2年","参照标准":"JB/T 6382.1-2007"} |
| 冲压弯头 | Ф478*8 | 8.00 | 件 | {"规格型号":"Ф478*8","公称直径":"478mm","角度":"90°","弯曲半径":"1.5D","公称压力":"1.6MPa","材质":"20#钢"} |
| 冲压弯头 | Ф60*5R/90° | 70.00 | 件 | {"规格型号":"Ф60*5R/90°","公称直径":"60mm","角度":"90°","弯曲半径":"1.5D","公称压力":"1.6MPa","材质":"20#钢"} |
| 冲压弯头 | Ф273*7/R=1.5D/20#*90 | 28.00 | 件 | {"规格型号":"Ф273*7/R=1.5D/20#*90°","公称直径":"*","角度":"90°","弯曲半径":"1.5D","公称压力":"1.6MPa","材质":"20#钢"} |
| 钢制法兰 | 212*146*12 | 500.00 | 个 | {"规格型号":"212*146*12","公称压力":"1.6","公称通径":"110","材质":"钢Q235","特殊要求":"毛坯无镀层，基面平整，无凹凸、变形、残缺等影响使用的缺陷。质保期两年。供方提供材质证明、检测报告或合格证。","参照标准":"GB/T 9112-2010","备注":"如到货与技术要求不符做退换货处理，由此产生的费用全部由供方承担。"} |
| 冲压弯头 | Ф114 | 30.00 | 个 | {"规格型号":"Ф114","公称直径":"100mm","壁厚":"5mm","表面处理":"刷黑油防腐","角度":"90°","弯曲半径":"R=1.5D","公称压力":"1.6Mpa","材质":"20#","使用寿命":"730天","参照标准":"GB/T 12459-2017"} |
| 三通 | DN50-16/304 | 10.00 | 个 | {"规格型号":"DN50-16/304","公称直径":"50mm","壁厚":"4mm","表面处理":"无","角度":"90°","公称压力":"1.6Mpa","连接方式":"焊接","材质":"304不锈钢","特殊要求":"内外表面光滑、无毛刺","使用寿命":"1095天","参照标准":"GB/T 12459-2017","备注":"若备件不符合技术要求或出现质量问题,厂家应及时给予退换货,由此产生的费用由供货方承担."} |
| 无缝冲压等径三通 | Ф89 | 20.00 | 个 | {"规格型号":"Ф89","公称直径":"DN80","壁厚":"5mm","表面处理":"刷黑油防腐","角度":"90°","公称压力":"1.6Mpa","连接方式":"焊接","材质":"20#","特殊要求":"外表光滑无毛刺，无锈蚀","使用寿命":"3650天","参照标准":"GB/T 12459-2017"} |
| 镀锌弯头 | DN65 | 20.00 | 个 | {"规格型号":"DN65","公称直径":"65mm","壁厚":"4.5mm","表面处理":"热镀锌","连接方式":"螺纹","角度":"90°","弯曲半径":"长半径95mm短半径64mm","公称压力":"1.6Mpa","材质":"玛钢","特殊要求":"丝扣均匀,无毛刺","使用寿命":"4380天","参照标准":"GB/T 3287-2011","备注":"NC57历史编码[*]不满足提报要求；验收：到货备件必须满足上述尺寸要求，对于不符合的要求退换货处理，所产生的费用由卖方承担。"} |
| 铁法兰盘 | DN400 | 10.00 | 个 | {"规格型号":"DN400","公称压力":"1Mpa","公称通径":"400mm","材质":"碳钢","特殊要求":"无","参照标准":"GB/T 9119-2010"} |
| 钢塑转换 | De200/DN150 | 5.00 | 支 | {"规格型号":"De200/DN150","公称压力":"1.6Mpa","适用介质":"天然气","材质":"聚*烯/20#钢","标准尺寸比":"SDR11","特殊要求":"钢管段外表面作防腐处理","使用寿命":"7300天","参照标准":"GB 26255.2-2010","备注":"本产品如有与技术要求不符之处，供货单位应进行退换货处理，由此所发生的一切费用，由供货单位承担。"} |
| 冲压弯头 | DN40 | 2.00 | 个 | {"规格型号":"DN40","公称直径":"40mm","壁厚":"3.5mm","角度":"90°","弯曲半径":"60","公称压力":"1.6Mpa","材质":"20#钢"} |
| 钢制法兰 | 155*79*10 | 300.00 | 个 | {"规格型号":"155*79*10","公称压力":"1.6Mpa","公称通径":"63mm","材质":"钢Q235","特殊要求":"毛坯无镀层，基面平整，无凹凸、变形、残缺等影响使用的缺陷。质保期两年。供方提供材质证明、检测报告或合格证。","参照标准":"GB/T 9112-2010","备注":"如到货与技术要求不符做退换货处理，由此产生的费用全部由供方承担。"} |
| 无缝冲压同心大小头 | Ф89*57 | 20.00 | 个 | {"规格型号":"Ф89*57","公称直径":"DN80*50","大头外径":"ф89mm","小头外径":"ф57mm","大头内径":"ф83mm","小头内径":"ф51mm","公称压力":"1.6Mpa","连接方式":"焊接","壁厚":"6mm","表面处理":"刷黑油防腐","材质":"20#","内衬材质":"无","内衬厚度":"无","特殊要求":"表面光滑无毛刺、无锈蚀","使用寿命":"3650天","参照标准":"GB/T 12459-2017"} |
| 不锈钢弯头 | DN150/316L | 1.00 | 个 | {"规格型号":"DN150/316L","公称直径":"150mm","壁厚":"5mm","表面处理":"表面应无残损、锈蚀、碰伤、气孔、夹渣、毛刺等情况","连接方式":"焊接","角度":"90°","弯曲半径":"1.5D","公称压力":"1.6Mpa","材质":"不锈钢316L","特殊要求":"通用件,主要输送介质为蒸汽、水、油等","使用寿命":"≥1825天","参照标准":"GB/T 12459-2017","备注":"到厂附有出厂检测报告原件或具有检测报告原件相同效力的复印件.经验收不能满足该产品技术要求或验收标准,供应商应无条件退货,并按照物资提报的技术要求重新发货,产生的费用由供应商承担."} |
| 招标信息 | |||
|---|---|---|---|
| 招标单位 | (略) | 项目名称 | 管道、法兰 |
| 质保期 | 报名截止日期 | ||
| 招标邮箱 | *@*ttp://** | ||
| 竞标保证金信息 | |||
|---|---|---|---|
| 项目保证金 | 2000.00元 | 帐户名称 | 山东新南 (略) |
| 帐号 | * | 开户行 | 中国银行龙口南山支行 |
| 备注 | |||
| 备注：竞价 (略) 转账，不支持个人名义转账或银行柜台现金转账。 | |||
| 供应审计部招标联系人信息 | |||
|---|---|---|---|
| 标书联系人 | 无 | 办公电话 | 无 |
| 邮件 | 无 | ||
| 标书汇款相关信息 | |||
|---|---|---|---|
| 账户名称 | 无 | 账号 | 无 |
| 开户行 | 无 | 行号 | 无 |
| 标书收费标准 | 地址、电话 | 无 | |
| 备注： (略) 转账，不支持个人名义转账或银行柜台现金转账。注明标书费的用途或投标项目名称。 | |||
| 物品名称 | 规格型号 | 数量 | 单位 | 描述 |
|---|---|---|---|---|
| 双金属复合耐磨直管 | DN450 | 5.00 | 件 | 1.名称：双金属复合耐磨直管 2.规格型号：DN450 3.执行标准：GB/T 26652-2011 4.材质：外管Q345B，内衬KMTBCr28 5.单位：件 6.使用寿命：5年 7.技术要求：直管长度1.5米，两侧带非标法兰,可以直接连接D480×14管道上的DN450标准法兰（A系列）。外管规格D510×10mm，内衬管内径Dn=448mm，管内耐磨层厚度H不低于20，复合管外层采用普通钢管材质Q345B，内衬采用高铬耐磨合金材质KMTBCr28，在高温热铸（焊）状态下整体复合而成，耐磨层硬度不低于HRC46。 8.验收标准：提交材质证明，附产品合格证，来货与技术要求不符，供应商予以免费退换货处理。 |
| 双金属复合耐磨弯头 | DN450 | 2.00 | 件 | 1.名称：双金属复合耐磨弯头 2.规格型号：DN450 3.执行标准：GB/T 26652-2011 4.材质：外管Q345B，内衬KMTBCr28 5.单位：件 6.使用寿命：5年 7.技术要求：弯头为90°两侧带非标法兰, 可以直接连接D480×14管道上的DN450标准法兰（A系列）。弯头外管规格D510×10mm，内衬管内径Dn=448mm，弯头外侧耐磨层厚度H1=22，弯头内侧耐磨层厚度H2=20,复合管外层采用普通钢管材质Q345B，内衬采用高铬耐磨合金材质KMTBCr28，在高温热铸（焊）状态下整体复合而成，耐磨层硬度不低于HRC46，弯头进料方向直管L1长度200mm，出料方向直管L2长度300mm。 8.验收标准：提交材质证明，附产品合格证，来货与技术要求不符，供应商予以免费退换货处理。 |
| 法兰盘 | DN150 | 8.00 | 片 | {"规格型号":"DN150","公称压力":"1.6Mpa","公称通径":"150mm","材质":"Q235B","特殊要求":"密封面需有水纹密封线；使用寿命：≥1095天；螺栓孔数：8孔","参照标准":"GB/T 9124.1-2019","备注":"验收标准：到货与技术要求不符时，供应商无条件退换货处理。"} |
| 法兰盘 | DN100/PN16 | 138.00 | 片 | {"规格型号":"DN100/PN16","公称压力":"1.6Mpa","公称通径":"100mm","材质":"Q235A","特殊要求":"使用寿命2190天,密封面需有水纹密封线.","参照标准":"GB/T 9124.1-2019","备注":"到货与技术附件不符予以退/换货."} |
| 法兰盘 | DN40/PN16 | 2.00 | 片 | {"规格型号":"DN40/PN16","公称压力":"1.6MPa","公称通径":"40mm","材质":"碳钢Q235A"} |
| 法兰盘 | DN50-16 | 24.00 | 片 | {"规格型号":"DN50-16","公称压力":"1.6MPa","公称通径":"50mm","材质":"Q235B/国标","参照标准":"GB/T 9112~9124-2010钢制管法兰"} |
| 法兰盘 | DN32 | 2.00 | 片 | {"规格型号":"DN32","公称压力":"1.6MPa","公称通径":"32mm","材质":"Q235A","参照标准":"GB/T 9119-2010"} |
| 冲压弯头 | Φ89*5/R=5D/90° | 35.00 | 个 | {"规格型号":"Φ89*5/R=5D/90°","公称直径":"89mm","壁厚":"5mm","角度":"90°","弯曲半径":"R=5D","公称压力":"1.6Mpa","材质":"20#钢","使用寿命":"5年"} |
| 冲压弯头 | DN32/20# | 50.00 | 个 | {"规格型号":"DN32/20#","公称直径":"32mm","壁厚":"5mm","角度":"90°","弯曲半径":"R=1.5D","公称压力":"1.6Mpa","材质":"20#钢","使用寿命":"5年"} |
| 冲压弯头 | Φ159*20/R=1.5D/90度 | 5.00 | 件 | {"规格型号":"Φ159*20/R=1.5D/90度","公称直径":"159mm","壁厚":"20mm","表面处理":"表面无残损、锈蚀、碰伤、气孔、夹渣、毛刺","连接方式":"焊接","角度":"90°","弯曲半径":"1.5D","公称压力":"10Mpa","材质":"20#碳钢","特殊要求":"无","使用寿命":"700天","参照标准":"GB/T 12459-2017","备注":"验收标准：厂家到货附带材质报告单及合格证，达不到技术要求，要求厂家无偿换货，在使用过程中达不到使用寿命，要求厂家赔付！"} |
| 冲压弯头 | Φ159*6/R=1.5D/20# | 10.00 | 件 | {"规格型号":"Φ159*6/R=1.5D/20#","公称直径":"159mm","角度":"90°","弯曲半径":"1.5D","公称压力":"1.6MPa","材质":"20#钢"} |
| 冲压弯头 | DN32 | 5.00 | 个 | {"规格型号":"DN32","公称直径":"32mm","角度":"90°","弯曲半径":"48/32","公称压力":"1.6Mpa","材质":"20#钢","使用寿命":"12年"} |
| 冲压弯头 | DN76*5 | 2.00 | 个 | {"规格型号":"DN76*5","公称直径":"76mm","壁厚":"5","角度":"90°","弯曲半径":"114","公称压力":"1.6Mpa","材质":"20#钢","使用寿命":"2年","参照标准":"JB/T 6382.1-2007"} |
| 冲压弯头 | Ф478*8 | 8.00 | 件 | {"规格型号":"Ф478*8","公称直径":"478mm","角度":"90°","弯曲半径":"1.5D","公称压力":"1.6MPa","材质":"20#钢"} |
| 冲压弯头 | Ф60*5R/90° | 70.00 | 件 | {"规格型号":"Ф60*5R/90°","公称直径":"60mm","角度":"90°","弯曲半径":"1.5D","公称压力":"1.6MPa","材质":"20#钢"} |
| 冲压弯头 | Ф273*7/R=1.5D/20#*90 | 28.00 | 件 | {"规格型号":"Ф273*7/R=1.5D/20#*90°","公称直径":"*","角度":"90°","弯曲半径":"1.5D","公称压力":"1.6MPa","材质":"20#钢"} |
| 钢制法兰 | 212*146*12 | 500.00 | 个 | {"规格型号":"212*146*12","公称压力":"1.6","公称通径":"110","材质":"钢Q235","特殊要求":"毛坯无镀层，基面平整，无凹凸、变形、残缺等影响使用的缺陷。质保期两年。供方提供材质证明、检测报告或合格证。","参照标准":"GB/T 9112-2010","备注":"如到货与技术要求不符做退换货处理，由此产生的费用全部由供方承担。"} |
| 冲压弯头 | Ф114 | 30.00 | 个 | {"规格型号":"Ф114","公称直径":"100mm","壁厚":"5mm","表面处理":"刷黑油防腐","角度":"90°","弯曲半径":"R=1.5D","公称压力":"1.6Mpa","材质":"20#","使用寿命":"730天","参照标准":"GB/T 12459-2017"} |
| 三通 | DN50-16/304 | 10.00 | 个 | {"规格型号":"DN50-16/304","公称直径":"50mm","壁厚":"4mm","表面处理":"无","角度":"90°","公称压力":"1.6Mpa","连接方式":"焊接","材质":"304不锈钢","特殊要求":"内外表面光滑、无毛刺","使用寿命":"1095天","参照标准":"GB/T 12459-2017","备注":"若备件不符合技术要求或出现质量问题,厂家应及时给予退换货,由此产生的费用由供货方承担."} |
| 无缝冲压等径三通 | Ф89 | 20.00 | 个 | {"规格型号":"Ф89","公称直径":"DN80","壁厚":"5mm","表面处理":"刷黑油防腐","角度":"90°","公称压力":"1.6Mpa","连接方式":"焊接","材质":"20#","特殊要求":"外表光滑无毛刺，无锈蚀","使用寿命":"3650天","参照标准":"GB/T 12459-2017"} |
| 镀锌弯头 | DN65 | 20.00 | 个 | {"规格型号":"DN65","公称直径":"65mm","壁厚":"4.5mm","表面处理":"热镀锌","连接方式":"螺纹","角度":"90°","弯曲半径":"长半径95mm短半径64mm","公称压力":"1.6Mpa","材质":"玛钢","特殊要求":"丝扣均匀,无毛刺","使用寿命":"4380天","参照标准":"GB/T 3287-2011","备注":"NC57历史编码[*]不满足提报要求；验收：到货备件必须满足上述尺寸要求，对于不符合的要求退换货处理，所产生的费用由卖方承担。"} |
| 铁法兰盘 | DN400 | 10.00 | 个 | {"规格型号":"DN400","公称压力":"1Mpa","公称通径":"400mm","材质":"碳钢","特殊要求":"无","参照标准":"GB/T 9119-2010"} |
| 钢塑转换 | De200/DN150 | 5.00 | 支 | {"规格型号":"De200/DN150","公称压力":"1.6Mpa","适用介质":"天然气","材质":"聚*烯/20#钢","标准尺寸比":"SDR11","特殊要求":"钢管段外表面作防腐处理","使用寿命":"7300天","参照标准":"GB 26255.2-2010","备注":"本产品如有与技术要求不符之处，供货单位应进行退换货处理，由此所发生的一切费用，由供货单位承担。"} |
| 冲压弯头 | DN40 | 2.00 | 个 | {"规格型号":"DN40","公称直径":"40mm","壁厚":"3.5mm","角度":"90°","弯曲半径":"60","公称压力":"1.6Mpa","材质":"20#钢"} |
| 钢制法兰 | 155*79*10 | 300.00 | 个 | {"规格型号":"155*79*10","公称压力":"1.6Mpa","公称通径":"63mm","材质":"钢Q235","特殊要求":"毛坯无镀层，基面平整，无凹凸、变形、残缺等影响使用的缺陷。质保期两年。供方提供材质证明、检测报告或合格证。","参照标准":"GB/T 9112-2010","备注":"如到货与技术要求不符做退换货处理，由此产生的费用全部由供方承担。"} |
| 无缝冲压同心大小头 | Ф89*57 | 20.00 | 个 | {"规格型号":"Ф89*57","公称直径":"DN80*50","大头外径":"ф89mm","小头外径":"ф57mm","大头内径":"ф83mm","小头内径":"ф51mm","公称压力":"1.6Mpa","连接方式":"焊接","壁厚":"6mm","表面处理":"刷黑油防腐","材质":"20#","内衬材质":"无","内衬厚度":"无","特殊要求":"表面光滑无毛刺、无锈蚀","使用寿命":"3650天","参照标准":"GB/T 12459-2017"} |
| 不锈钢弯头 | DN150/316L | 1.00 | 个 | {"规格型号":"DN150/316L","公称直径":"150mm","壁厚":"5mm","表面处理":"表面应无残损、锈蚀、碰伤、气孔、夹渣、毛刺等情况","连接方式":"焊接","角度":"90°","弯曲半径":"1.5D","公称压力":"1.6Mpa","材质":"不锈钢316L","特殊要求":"通用件,主要输送介质为蒸汽、水、油等","使用寿命":"≥1825天","参照标准":"GB/T 12459-2017","备注":"到厂附有出厂检测报告原件或具有检测报告原件相同效力的复印件.经验收不能满足该产品技术要求或验收标准,供应商应无条件退货,并按照物资提报的技术要求重新发货,产生的费用由供应商承担."} |
招投标大数据
最近搜索
无
热门搜索
无
